Current tent styles
With modern materials, tent manufacturers have great freedom to vary types and styles and shapes of tents.
* The poles effectively hold the tent in the required shape.
* Poles which dismantle for ease of transport are either colour-coded or linked by chain or cord, so there is little doubt as to which poles connect where.
* Relatively few guy ropes are needed (sometimes none).
* The exact positioning of any guy ropes is not too critical.
Rigid poles
Many tents which use rigid steel poles are free-standing and do not require guy ropes, though they may require pegs around the bottom edge of the fabric. These tents are usually so heavy (25 to 80 kg) that it takes a rather strong wind to blow them away.
* Frame tents are double-skin tents. They have a living area and one or more cotton/nylon/polyester inner tents. The outer tent is draped over a free-standing steel frame, and may be made of canvas or polyester (the latter often has a hydrostatic head of 3000mm, i.e. three season camping). The living area is generally at least as large as the sleeping area, and there may be a specific section with window and extra air vents for use as a kitchen. The walls are nearly vertical and are typically about 150 to 180 cm high (5 ft to 6 ft). The center of the gently sloping roof is often 210 cm (7 ft) high or more and provides reasonable headroom throughout. The smaller 2-person models were less than 3 metres square (10 ft), but these have largely been replaced by dome or tunnel tents. The larger 8-person models may exceed 5 metres (16 ft) in length and/or width.
* Cabin tents are single-skin tents used mainly in the USA. They often have nylon walls, polyester roof, and a polyethylene floor, plus an awning at one or both ends. With a hydrostatic head of only 1000 mm, they may best be considered as summer tents. Removable internal dividers allow the cabin to be split into 'rooms'. Sizes may range from 13 ft by 8 ft (2 rooms) up to 25 ft by 10 ft (4 rooms), with wall and roof heights similar to those of frame tents. There are three separate pole units, with each unit consisting of two uprights and a connecting ridge. These pole units support the centre and ends of the roof, and are usually outside the tent.
Flexible poles
Flexible poles used for tents in this section are typically between 3 and 6 metres long (10 and 20 feet). Cheap poles are made of tubes of fibreglass with an external diameter less than 1 cm (1/3 inch), whereas more expensive aluminium alloys are the material of choice for added strength and durability. For ease of transportation, these poles are made in sections some 30 cm to 60 cm long (1 to 2 ft), with one end of each section having a socket into which the next section can fit. For ease of assembly, the sections for each pole are often connected by an internal elastic cord running the entire length of the pole.
This is a basic dome tent, shown without rain fly or stakes.
Assembling a modern flexible poled tent (Terra Nova Duolite). This tent has external poles linked together by hubs.
* Dome tents have a very simple structure and are available in a wide variety of sizes ranging from lightweight 2-person tents with limited headroom up to 6 or 9-person tents with headroom exceeding 180 cm (6 ft). These may be single wall, or single-wall with partial flysheet, or double wall. Depending on the pole arrangement, some models pitch outer-tent first, while others pitch inner-tent first. The former helps keep the inner tent dry, but the latter is easier to pitch.
The basic dome has a rectangular floor and two poles which cross at the peak; each pole runs in a smooth curve from one bottom corner, up to the peak, and then down to the diagonally opposite bottom corner. There are usually special fittings at each corner which fit into sockets at the ends of each pole - pole tension keeps everything in shape. The poles can run on either the inside or outside of the tent fabric. When located on the interior, poles are held in place by a variety of means including hook and loop style straps, clips, and other fastening hardware. Poles that are located on the outside of the tent fabric are attached via fabric pole sleeves or plastic clips. Dome tents do not require guy ropes and pegs for structural integrity as they are considered free-standing, but must be pegged down in high winds.
The basic dome design has been modified extensively, producing tents with three poles, tents with irregularly-shaped bases, and other unusual types. A common variation is to add a third pole between two adjacent corners; this is angled away from the tent and supports an extension of the flysheet, to give a porch/storage area.
Tunnel tent
* Tunnel tents may offer more usable internal space than a dome tent with the same ground area, but almost always need guy ropes and pegs to stay upright. These are almost always double wall tents. Sizes range from 1-person tents with very limited headroom up to 8 or 10-person tents with headroom exceeding 180 cm (6 ft). Tunnel tents have a low end profile making them great for high wind situations.
Possibly the first tunnel tent was that produced by Hayes Mountain Equipment, Australia in 1965 to the design of Barry Hayes. It was successfully tested by the Monash University Mountaineering Club on Mount Baw Baw, Victoria, where it withstood 70 mph winds. It was subsequently used during the construction of the Melbourne University Mountaineering Club dome hut on Mount Feathertop.
A basic tunnel tent uses three flexible poles, arranged as three parallel hoops, with tent fabric attached to form a tunnel. The most common designs have a sleeping area at one end and a porch/storage/living area at the other. Smaller designs may use only 2 poles and larger designs may use 4 poles; the latter may have a sleeping area at each end and a living area in the middle.
* Hybrid dome/tunnel tents are now common. One variation is to use a basic dome as the sleeping area; one or two hooped poles to one side are linked by a tunnel to the dome to provide a porch. Another variation is to use a large dome as the living area, with up to 4 tunnel extensions to provide sleeping areas.
* Geodesic tents are essentially dome tents with 2 or more extra poles which criss-cross the normal two poles to help support the basic shape and minimise the amount of unsupported fabric. This makes them more suitable for use in snowy conditions and in strong winds. To help withstand strong winds they are rarely more than 120 or 150 cm high (4 to 5 ft).
* Single-hoop tents use just one flexible pole and are often sold as light-weight 1 or 2-person tents. These are the modern equivalent of older style pup tents, and have the same feature of somewhat limited headroom. Different styles may have the pole going either along or across the tent.
* The pop-up tent is a recent innovation . This type of tent is equipped with built-in very flexible hoops so that when the tent is unpacked, it springs into shape immediately, and so is extremely easy to set up. Such tents are usually single-skinned and are generally aimed at the one-season or children's end of the market; their high flexibility makes them unsuitable for use in windy situations. After use the tent is packed down into a thick disc shape.
Inflatable airbeams
Inflatable pole supports, also known as airbeams, serve as rigid structural supports when inflated but are soft and pliable when deflated. Much like a bicycle tube and tire, airbeams are often composed of a highly dimensionally stable (i.e. no stretch) fabric sleeve and an air-holding inner bladder. However, other airbeam constructions consist of coated fabrics that are cut and manufactured to its intended shape by a method such as thermal welding. Depending on the desired tent size, airbeams can be anywhere from 2-40 inches in diameter, inflated to different pressures.[2] High pressure airbeams (40-80 psi) that are filled by compressors are most often used in larger shelters, whereas low pressure beams (5-7 psi) are preferred for recreational use.[3] The relatively low pressure enables the use of a manual pump to inflate the airbeam to the desired level. Airbeams have the unique quality of bending, rather than breaking, when overloaded. Tents that use inflatable airbeams are structured almost identical to those that use flexible poles.
Inflatable airbeam tunnel tent
* Dome tents that use inflatable airbeam support are available in a variety of sizes ranging from lightweight 2-person to larger 6+ person shelters, and are virtually identical to the arrangement of flexible-pole supported dome tents. Beams are usually integrated into the tent shell such that they do not have to be reinserted every time setup occurs. Airbeams can be located on either the inside or outside of the tent shell. Similar to the pole-supported construction, airbeam supported dome tents are free standing but should be staked out with pegs and guyout lines to increase stability and strength.
* Tunnel tents are a common form of airbeam supported tents because their size can be easily modified by adding additional hoops. Military applications use this style of tent for a range of purposes including medical shelters, helicopter enclosures, and airplane hangars.[4] In these constructions, hoops are generally identical in size. In commercial airbeam supported tents, the hoops can be different sizes. Tunnel tents tend to withstand high winds well because of their low profile shape. However, the tents are not freestanding and must be anchored and guyed out securely.
Older tent styles
Most of these tent styles are no longer generally available. Most of these are single-skin designs, with optional fly sheets for the ridge tents.
All the tents listed here had a canvas fabric and used a substantial number of guy ropes (8 to 18). The guys had to be positioned and tensioned fairly precisely in order to pitch the tent correctly, so some training and experience were needed. This made these styles relatively unsuitable for casual or occasional campers. Pup tents might use wooden or metal poles, but all the other styles mentioned here used wooden poles.
* A pup tent is a small version of a ridge tent intended for 2 or 3 people. It usually has a rectangular floor of size ranging from 4 ft by 6 ft up to 6 ft by 8 ft, and ridge heights ranging from 3 ft up to 5 ft. The side walls are usually about 1 ft high. There are guy ropes for each pole, at each corner, and in the centre of each side, and these guy ropes help to maintain the required shape. Earlier versions had a single upright pole at each end, while later versions often have two poles at each end, arranged rather like an 'A' shape, in order to make access easier. Some models have a horizontal ridge pole joining the tops of the end poles to support the centre of the tent.
* A ridge tent can sleep 5 to 8 people. They usually have a rectangular floor of size ranging from 8 ft by 10 ft up to 10 ft by 16 ft, and ridge heights around 6 ft to 7 ft. The side walls are usually about 3 ft high. They normally have a single upright pole at each end with the tops joined by a horizontal ridge pole. Longer models might have an additional upright pole in the centre to help support the ridge pole. They often have two guy ropes at each corner, and guy ropes every 2 ft along the sides. If strong winds are expected then two additional storm guy ropes are attached to the top of each pole.
* A square centre-pole tent was often used for family camping in the first half of the 20th century. Despite the use of 9 poles and 12 guy ropes, such a tent could be pitched by an (experienced) family of four in some 10 to 15 minutes. These tents had a square floor of size ranging from 8 by 8 ft up to 15 by 15 ft. There were poles about 5 ft high at each corner and in the middle of each side, and a 10 ft or 12 ft pole in the centre - the walls were vertical and the roof was pyramid-shaped, so there was plenty of headroom over most of the tent.
* A Sibley tent (bell tent) had a circular floor plan some 10 ft to 15 ft across, a single central pole some 10 ft high, and walls about 3 ft high. Guy ropes were connected every 2 ft around the top of the walls - these had to carefully tensioned to hold the pole upright and keep the tent in shape.
Larger tents
These larger tents are seldom used for sleeping.
* "Party tents" or "marquees" are common for large weddings, fairs, corporate hospitality events and other gatherings. They are made from PE (polythene) or the better quality ones from PVC. 'DIY' marquees are available up to 20 feet (6m) wide. 30 to 150 feet (9m to 45m) widths are very expensive and require specialized equipment and skill to erect, so they must usually be rented. Many corporations own large (9m to 45m wide) marquee tents but have them installed and maintained by qualified professionals. Party tents are held down with tensioned ratchets and/or stakes. Sizes range from 10 x 10 feet (3m x 3m) to 150 x 400 feet (45m x 120m). Marquees / party tents are dramatic and very strong.
* Traditional Pole Marquees - consist of canvas and more recently PVC, under tension by means of centre poles, side poles and guy ropes which are attached to ground stakes hammered into soft surfaces only such as a lawn or field. Hand made of white cotton canvas, traditional poled marquees are more attractive but much less practical and versatile than aluminium frame marquees. The modern PVC traditional pole marquee was introduced due to the material being easier to clean than woven canvas and giving them a longer hire life span.
* Aluminium Frame Marquees - Aluminium frame tents have no centre poles or guy ropes, can be erected on any surface and adjacent to buildings or annexe tents. Much more stable and can span a much wider area over pools, flower beds or trees.
Typical 20'x20' High Peak Frame Tent set up at Events Party & Tent Rentals for Demonstration
* A newer category of the Marquee/Party tents is the High Peak Frame Tents (known by several brand names like "frame & cable", "vista", "pinnacle", etc). These tents have the advantage of the pole tents with the high top, ease of installation, cleaner look, and fewer parts. They also have the advantage of the Frame Tents as they do not have support pole(s) on the inside of the tent that touches the ground. The high top look is accomplished by using a "floating pole", which is a pole that sits on cables that run across the tent interior from the top of the sides. Most tent manufactures are now making these tents and they come in a variety of sizes and shapes that can be joined together to meet the needs of unique space requirements.
* Marquee tents typically have interchangeable parts, which allow for a rental company to easily expand to larger sizes. Tents can be ordered in a variety of colours. However, white is by far the most popular colour. Skylights can also be built into the fabric, which allow a greater amount of light to enter and is useful if walls are being used. Walls can also be ordered with clear vinyl windows in them.
* "Bail Ring Tents" are usually tents that are 100 to 150 feet (30m x 45m) wide and expandable to any length. They can be made from either vinyl or canvas. The purpose of the bail ring style is to raise an enormous amount of material "the tent" off the ground without using heavy machinery. Initially, the center poles are raised and guyed out to stakes after which the tent is spread out and connected to the bail ring using shackles. Once the outside of the tent is raised a crew of men can go under the tent and start raising the bail ring up the center pole using a system of pulleys. This style of tent is not as popular as it was in the past due to the advancement of forklifts and skidsteers. There was a time when even smaller tents 40 to 100 feet (12m to 30m) were often raised and set using a bail ring.
* The four Major golf tournaments have tents set up they are usually 40 x 40 feet (12m x 12m).
* Tents or marquees are often hired from specialist companies.
* A "Rub Hall" is a large tent used primarily as emergency warehousing.
* A circus tent usually has one or more oval or circular arenas surrounded by tiered seating which might accommodate thousands of people. Nowadays such large tents are made of some artificial fibre (polyester or vinyl) and are often erected with the help of cranes. In earlier times it was common for the circus elephants to be used as a source of power for pulling ropes to haul the canvas into position.
|
|
